PEEPLNK

1. CWR-2153 CSR-23928 Toolpath In Assembly mode, when the 3 Axis Toolpath Generation Method is set to Advanced, the toolpath for the Pattern Project operation with a Contain Area fails to generate. However, if the Contain Area is suppressed, toolpath gets successfully generated.
2. CW-128050 CSR-26063 License The Z Level option of "Combination Cycle" must be active with the License Module "2.5X Mill Plus".
3. CW-127021 CSR-25765 System When CAMWorks is loaded as an add-in within SOLIDWORKS and user attempts to open the specific Assembly file, it causes the SOLIDWORKS application to crash. To open the Assembly file successfully, user must deactivate the CAMWorks add-in.
4. CW-126953 CSR-25753 Simulation In CAMWorks Virtual Machine, for the specific Machine, the Offset table of that machine gets displays incorrectly during Machine Awareness display in graphics area.
5. CW-126800 CSR-25641 Feature The boss and the fillet body of the specific part can't be detected by the side taper "Auto Detect" when the boss at the part height value is 0.1 mm or less.
6. CW-126796 CSR-25638 System For the specific assembly, if you delete/empty the recycle bin and then click on Save, it shows error indicating a problem in saving CAMWorks entities.
7. CW-126685 CSR-25618 Setup Sheet Setup Sheets generated do not display correct Assembly Tool Protrusion after reselecting the Tool Crib.
8. CW-126678 CSR-25544 API Provide an API to get the user-defined text string in square brackets after the Operation Names (including Postm Operation names )in the CAMWorks Operation tree.
9. CW-126675 CSR-25556 System If a Multiaxis Mill operation has the pole handling angle tolerance value assigned as 0, then it crashes during post processing.
10. CW-126662 CSR-25580 Simulation In CAMWorks 2024, when importing a Machine, if the Machine contains an STL file with "Ü" character present in the ✅File Name, then the Machine import fails.
11. CW-126403 CSR-25459 System When the specific CAM data is imported to the specific part file, CAMWorks crashes.
12. CW-126358 CSR-25370 Operation For the specific Turn part, when a user-defined Turn Holder/Insert is used for one of its operations, CAMWorks takes too much time to display the Holder/Insert. It also gets difficult to move or rotate the Holder/insert in the graphics area, rendering it almost unusable.
13. CW-126111 CSR-25434 System The specific CAM data causes SOLIDWORKS To crash when opening the programmed assembly file.
14. CW-126069 CSR-25422 Toolpath For the specific part, if a high speed link is used for a Rough Mill toolpath, then it generates some unwanted moves that gouges the part.
15. CW-126064 CSR-25396 Toolpath For the specific Mill part, the option of 180 degree (change start point) fails when a larger tool is assigned.
16. CW-126055 CSR-25409 Operation When a new sub-spindle operation is inserted, then the Spindle direction saved with the sub-spindle operation template does not load correctly.
17. CW-125843 CSR-25406 System When the specific Mill part is loaded in CAMWorks, it causes CAMWorks to crash when user attempts to access the CAMWorks Feature Tree or Operation Tree.
18. CW-125666 CSR-24145 Assembly Using the functionality to combine operations in the specific assembly does not combine all selected operations.
19. CW-125658 CSR-25302 Simulation If Virtual Machine template APT file is saved in German language version of the CAMWorks Virtual Machine application and then imported in German language version of the CAMWorks application, then it fails to import.
20. CW-125583 CSR-25109 Toolpath In a Contour Mill operation, if there are multiple side cuts, then the Clearance plane is not observed.
21. CW-125544 CSR-25205 Toolpath For the specific Mill part, when generating the toolpath for the Face operation, CAMWorks fails to detect the Rectangular island present on the Face feature.
22. CW-125347 CSR-25126 Toolpath For the specific Mill part, an extra finish cut move is observed for Contour Mill toolpath when the ‘Single Cut Depth' checkbox is checked and the ‘Limited Look Ahead' with CNC compensation is active.
23. CW-125297 CSR-25067 Toolpath In Assembly mode, for the specific Assembly file, the Tool Orientation for the Setup gets flipped.
24. CW-125291 -- UIF In Machine awareness, in the UI of the importing machine, we have a checkbox labelled ‘Show housing' which shows the entire machine. However, in the toolbar, it is labelled as ‘Display housing'. The naming should be consistent.
25. CW-125252 CSR-24937 Assembly In CAMWorks Assembly mode, for the specific assembly, the Avoid areas defined are ignored by 2 Axis Rough Mill, Contour Mill, and 3 Axis VoluMill operations when generating the toolpath.
26. CW-125154 CSR-24959 Help In the Post_Processor_Reference.pdf UPG Help Document, the typographical error for the system variable named OPR_Z_FINISH [OPT_Z_FINISH] needs to be corrected.
27. CW-125007 CSR-24898 Toolpath The wrong entry move is observed on the Contour Move Bottom Finish when the Perimeter pass after is applied. The ramp entry is along the feature wall which is invalid. This happens when the irregular pocket contains the top chamfer/fillet.
28. CW-124965 CSR-24852 Post For the specific file, single instance in Patterned Contour Mill outputs incorrect Z values when posting.
29. CW-124937 CSR-24754 Toolpath CAMWorks 2021-2023 versions change the sequence order of the plunge toolpaths created in 2018 CAMWorks version.
30. CW-124930 CSR-24778 Toolpath Unnecessary paths are added in the Contour Mill, when "Limited look ahead" is checked in the NC tab and "Cut depth" is set to "Stay Down" in the Leadin tab. A path gets added that is not needed thereby causing the part to get damaged with the specific tool diameter.
31. CW-124400 CSR-24434 Toolpath For any Contour Mill operation, if the depth processing is selected as "depth by region" and negative depth allowance is added, then if the spring pass is added, it will not generate the toolpath.
32. CW-124318 CSR-24311 ShopFloor When trying to open the specific ShopFloor file, the ShopFloor application crashes without any warning message.
33. CW-123869 CSR-24144 Help For 3 Axis and Multiaxis Posting error codes, the description for each of the error codes needs to be documented in the context based Help file as the CAMworks error message doesn't contain any description.
34. CW-123336 CSR-24002 Toolpath For the specific Mill part, too many cleanup passes get generated for the Contour Mill operation that uses single depth cut.
35. CW-122056 CSR-23507 Simulation When the specific Assembly with multiple Contour Mill operations is simulated at a higher speed, an error message indicating inability to continue the simulation gets displayed. This happens only when the ‘Center cutting' checkbox option for the tool is unchecked.
36. CW-121901 CSR-23439 Toolpath The Islands are ignored on wrapped roughing operations when the island position is not the centerline of the cylinder.
37. CW-121579 CSR-23322 Toolpath In Assembly mode, any Contain area assigned to a VoluMill operation prevents the VoluMill toolpath from being calculated.
38. CW-121121 CSR-23132 Toolpath For the specific Mill-Turn part, islands are ignored by the wrapped Rough Mill operations.
39. CW-120321 CSR-22757 Assembly Contain and Avoid Areas are not correctly recognized in Assembly mode for the specific assembly.
40. CW-117274 CSR-21149 Help In UPG-2 Help file, update the help content written for the Header command SORT_BY_TURRET.
41. CW-116224 CSR-20845 Toolpath When generating the toolpath for the specific Assembly file, Avoid Areas being ignored on 4th axis.
42. CW-115869 CSR-20675 Toolpath The Contour Milling with CNC compensation on the curve feature generates the wrong toolpath at the leadin/out. This is observed only when the feature has the open end (not the closed curve).
43. CW-115094 CSR-20281 Toolpath For the specific part, the Profile Milling Overlap gouges the part when using the Look Ahead option.
44. CW-114640 CSR-19890 Toolpath For the specific customer part file, Contour Mill operation does not get generated for the irregular pocket feature.
45. CW-112838 CSR-18877 Operation For the specific Mill-Turn part, when trying to edit any operation by clicking on the ‘Edit Definition' command, it takes too much time to invoke and display the Operation Parameters dialog box.
46. CW-41249 10-9880 Help A brief document listing all available APIs available in CAMWorks sorted and tabulated as per their year of introduction would be of great help to users.